Show everyone you are a member of the Bubba Army with our official truck
window graphic. Looks great on any Truck or SUV rear window. Image is on
see-thru vinyl panel. Self stick and trim to size as needed.

The Window Graphic is available in 3 sizes listed below:

Small and Midsized vehicles - 6"x7 1/2"    $9.95

Pick-up Trucks - 12"x15"                         $29.95

SUV's - 67"x22"                                     $99.95

The Window Graphic should be at least as wide as the Side-to-Side
measurement, and at least as tall as the Top-to-Bottom measurement of your
Rear Window. You will trim off the excess just inside the window frame. If
you are between sizes, it is best to choose the next larger size up,
ensuring room to trim off excess and completely cover the Rear Window. Note:
If your truck window height is extremely small, such as 15 inches or less,
you will need to cut off more excess than usual. In this case make sure to
select a window graphic that has more background space available around the
central image. This way you will not encroach into the important part of the
image when cutting off the excess material.

Rear Window graphics are intended to be applied to rear windows only. Do not
apply to front windshields, driver side or passenger side windows. We make
no guarantee of application in regards to the local law in your area.
Consult your local laws regarding the application of window tint to vehicle
glass before making your purchase.

=VERY IMPORTANT INFORMATION=  

1.        STEP 1: PREPARE THE VEHICLE 

If you cannot bring the vehicle into a heated building, make sure that the
outside air temperature is above +40º F (+5º C). Pre-warming the car
interior during cold weather application will help insure proper adhesion.

2.        STEP 2: PREPARE THE GLASS 

Clean the outside glass surface which you will be applying the image to
thoroughly with soap and water. Make sure that the glass surface is dry and
residue free before applying your rear window graphic. Remember: The
pressure sensitive adhesive works best if mounted on VERY CLEAN GLASS.

3.        STEP 3: POSTION AND APPLY 

(Warning - Do not use a Heat Gun or use Water to apply - DRY MOUNT Only)

Use masking tape strips to pre-position the image on the vehicle prior to
removing the backing material. Carefully peel off adhesive backing from
behind the image and apply from one edge and work to the opposite side,
smoothing the image to prevent wrinkles. To remove any wrinkles, gently lift
up the image to where the wrinkle is, smooth out the wrinkle with your hand,
and continue applying.

4.        STEP 4: BOND AND TRIM 

To help adhesion, lay the disposable backing over the image and rub firmly
from the center to the sides of the image. You should have extra material to
trim off outside of the edge of your rear window glass. Trim the excess
material with an Exacto knife or similar tool to complete the installation.
The pressure sensitive adhesive bonds to the glass very well when first
applied but sets more firmly after a 24 hour period.

Avoid power car washes for the first week after application. For longer life
avoid using snow scrapers as they may damage the material. Treat this window
graphic as you would the painted surface of your car. Do not use abrasive
cleaners on the image. Avoid using rear windshield wipers as they will cause
premature wear of the material.

If your Truck is equipped with a Sliding Rear Cab window, it is recommended
that you wait one (1) week before sliding the window. This will insure that
the pressure sensitive adhesive is securely bonded to the glass.

5.        CAR WASHING: 

Avoid washing your window graphic for the first week after it is installed.
After this time you can safely take your vehicle through a commercial
brush-type car wash. We highly recommend hand washing for best results.

If you are using a Do-it-Yourself car wash, DO NOT HOLD THE WASH WAND CLOSER
THAN TEN (10") INCHES TO THE DECAL SURFACE.

Do not use abrasive cleaners on the rear window graphic.

6.        REMOVAL: 

The perforated film can be removed by using a thin scraper device. It is
best to start in one corner and lift up a small section. After this is done,
you can manually pull the image from the glass. As with any decal or
sticker, the warmer the outside temperature the easier the removal will be.
If any adhesive residue remains on the glass surface it can be cleaned with
any quality commercial glass cleaning liquid or citrus-based adhesive
remover / cleaner.

7.        CAUTION - DO NOT APPLY TO FRONT WINDSHIELD, DRIVER SIDE WINDOW OR
PASSENGER SIDE WINDOW!

RAINFALL, SNOWFALL AND CAR WASHES CAN CREATE CONDENSATION THAT WILL FILL THE
SMALL PERFORATIONS OF THE VINYL AND CAUSE REDUCED VISION UNTIL DRYING
OCCURS.

CONSULT YOUR LOCAL LAWS REGARDING THE APPLICATION OF WINDOW TINT TO VEHICLE
GLASS BEFORE ATTEMPTING TO INSTALL A REAR WINDOW GRAPHIC.